OPEN COM

From QB64 Phoenix Edition Wiki
Revision as of 16:59, 24 February 2023 by RhoSigma (talk | contribs)
Jump to navigation Jump to search

The OPEN COM statement is used to access a computer's serial port COM.


Syntax

OPEN "COMn: Speed, Parity, Bits, Stopbit, [Options]" [FOR {RANDOM|BINARY|OUTPUT|INPUT}] AS #P [LEN = byteSize]


Parameters

  • Speed (baud rate): 50, 150, 300, 600, 1200, 1800, 2400, 9600 (QBasic's maximum), 19200 or 115200 (QB64's maximum).
  • Parity: N (none), E (even), O (odd), S (space) or M (mark). Note: If 8 bits, use parity N for numerical data.
  • Bits = number of bits/byte: Valid numbers: 5, 6, 7 or 8
  • Stopbit = number of stop bits: Valid numbers: 1, 1.5 or 2
  • Optional COM port Options (separated by commas):
  • ASC : ASCII byte mode. End of line = CHR$(13). End of file = CHR$(26)
  • BIN : Binary byte mode. Default mode if ASC is not used(option not required).
Below ms is the timeout in milliseconds 1 to 65535. Zero ignores a timeout. Default without ms = 1000 :
  • CD[ms] : Time until timeout of DCD (Carrier Detect) line in. CD0 ignores timeouts.
  • CS[ms] : Time until timeout of CTS (Clear to Send) line in. CS0 ignores timeouts.
  • DS[ms] : Time until timeout of DSR (Data Set Ready) line in. DS0 ignores timeouts.
  • OP[ms] : Time until data lines become active. If timeout then OPEN fails, OP0 ignores timeouts.
  • RB[b] : Size of receive buffer in bytes when used. Default when not used = 512 bytes
  • TB[b] : Size of transmit buffer in bytes when used. Default when not used = 512 bytes
  • RS  : Supress detection of Request to Send (RTS) line.


Description

  • If any optional CD, CS, DS or OP timeouts occur the OPEN will fail or port access will stop. Try 0 to ignore.
  • QB64 can open any COMn port number from 1 to 9.
  • See Windows System Device Manager for COM port numbers and port addresses &H3F8, &H2F8, &H3E8 and &H2E8.
  • Four commas are required after the Speed, Parity, Bits, and Stopbit, even if none of the Options are used.
  • Other OPEN options are optional and in any order separated by commas within the OPEN command string.(See list below)
  • The optional FOR access mode can be OUTPUT, INPUT or RANDOM (default mode when no FOR statement is used).
  • Currently, QB64 only supports OPEN FOR RANDOM access using the GET/PUT commands in BIN mode.
  • Use the BIN option listed below for BINARY byte mode port access.
  • The LEN statement is also optional. The default record size is 512 bytes when not used.
  • Use the LOC(portnumber) function to determine that there is data in the receive buffer when the value is greater than 0.
  • OPEN AS number can use a FREEFILE value. Numbers used by files already open cannot be used by OPEN COM.
  • Keyword not supported in Linux or macOS versions


Examples

Example 1: Checking to see if a COM port exists. If the port does not exist QBasic will cause a Windows access error. 

ON ERROR GOTO Handler
FF = FREEFILE
comPort$ = "COM1:"                         'try a COM port number that does not exist
CONST comMode$ = "9600,N,8,1,CS0,DS0"      'Use 0 to avoid timeouts
OPEN comPort$ + comMode$ FOR RANDOM AS FF
IF errnum = 0 THEN PRINT "COM exists!

K$ = INPUT$(1)
END

Handler:
errnum = ERR
PRINT "Error:"; errnum
RESUME NEXT
Explanation: QB64 may create error 68 if COM is not found. Use a zero CD, CS, DS or OP timeout value to avoid COM timeouts.


Example 2: Opening a COM port with the BIN, CS0 and DS0 options in QB64. 

DIM bytestr AS STRING * 1  'one byte transfers
INPUT "COM port number #", port$  'any COM port number available

OPEN "COM" + port$ + ":9600,N,8,1,BIN,CS0,DS0" FOR RANDOM AS #1
DO 'main loop
    'receive data in buffer when LOC > 0
    IF LOC(1) THEN
       GET #1, , bytestr
       PRINT "[" + bytestr + "]";
    END IF
    'transmit (send)
    k$ = INKEY$
    IF LEN(k$) = 1 THEN
       k = ASC(k$)
       IF k >= 32 THEN     'ignore control key codes
           PRINT ">" + k$ + "<";
           bytestr = k$: PUT #1, , bytestr
       END IF
    END IF
LOOP UNTIL k$ = CHR$(27)
CLOSE #1: PRINT "Finished!"


Example 3: Sending string data from one COM port to another requires predefined length strings: 

DIM SHARED ByteIn AS STRING * 1 'One byte transfers
DIM SHARED Byte4 AS STRING * 4 'Four byte transfers

Byte4 = CHR$(254) + CHR$(175) + CHR$(0) + CHR$(3) 'Command code to query all 4 banks of switch input board.

OPEN "COM1:115200,N,8,1,BIN,CS0,DS0" FOR RANDOM AS #1 'Open port used to send commands.
OPEN "COM2:115200,N,8,1,BIN,CS0,DS0" FOR RANDOM AS #2 'Open port used to receive commands.

PUT #1, , Byte4 'Send the 4 byte command.

Start# = TIMER
DO UNTIL LOC(2) <> 0 'Check if there is data received at com2
    IF TIMER - Start# > .5 THEN EXIT DO 'Exit loop if no data arrives within .5 seconds.
LOOP

IF LOC(2) = 0 THEN 'If no data was received.....
    PRINT "No data received from COM port."
    END
END IF

PRINT "Received from COM2:";

DO UNTIL LOC(2) = 0 'Read data from COM2 until there is no more data.
    GET #2, , ByteIn
    PRINT ASC(ByteIn);
LOOP
END
Code courtesy of forum member Hydrofoiler


See also


Navigation:
Main Page with Articles and Tutorials
Keyword Reference - Alphabetical
Keyword Reference - By usage
Report a broken link
Retrieved from "https://qb64phoenix.com/qb64wiki/index.php?title=OPEN_COM&oldid=8054"